收藏本站
NXP Semiconductors
PCA9632
4-bit Fm+ I 2 C-bus low power LED driver
7.3.4 Group duty cycle control, GRPPWM
Table 9. GRPPWM - Group duty cycle control register (address 06h) bit description
Legend: * default value.
Address
06h
Register
GRPPWM
Bit
7:0
Symbol
GDC[7:0]
Access
R/W
Value
1111 1111
Description
GRPPWM register
When DMBLNK bit (MODE2 register) is programmed with 0, a 190 Hz fixed frequency
signal is superimposed with the 6.25 kHz Individual brightness control signal. GRPPWM
is then used as a global brightness control allowing the LED outputs to be dimmed with
the same value. The value in GRPFREQ is then a ‘don’t care’.
In the group dimming mode (DMBLNK = 0) global brightness for the 4 outputs is
controlled through 16 linear steps from 00h (0 % duty cycle = LED output off) to F0h
(93.75 % duty cycle = maximum brightness). In this mode only the 4 MSBs of the
GRPPWM[7:4] are used. Bits GRPPWM[3:0] are unused.
GDC ? 7 : 4 ? , 0000
duty cycle = -----------------------------------------
256
(4)
E.g., if GDC[7:4] = 1111, then duty cycle = 1111 0000 / 256 = 240 / 256 = 93.75 %.
When DMBLNK bit is programmed with 1, GRPPWM and GRPFREQ registers define a
global blinking pattern, where GRPFREQ contains the blinking period (from 24 Hz to
10.73 s) and GRPPWM the duty cycle (ON/OFF ratio in %).
In this mode, when GRPFREQ is programmed to provide a blinking with frequency
programmable from 24 Hz to 6 Hz, GRPPWM[7:2] is used to provide 64-step duty cycle
resolution from 0 % to 98.4 %. GRPPWM[1:0] bits are unused.
GDC ? 7 : 2 ? , 00
duty cycle = -----------------------------------
256
(5)
E.g., if GDC[7:2] = 111111, then duty cycle = 1111 1100 / 256 = 252 / 256 = 98.4 %.
When GRPFREQ is programmed to provide a blinking with frequency programmable from
6 Hz to 0.09 Hz (10.73 s), GRPPWM[7:0] is used to provide a 256-step duty cycle
resolution from 0 % to 99.6 %. In this case, all the 8 bits of the GRPPWM register are
used.
GDC ? 7 : 0 ?
duty cycle = --------------------------
256
E.g., If GDC[7:0] = 1111 1111, then duty cycle = 255 / 256 = 99.6 %.
Applicable to LED outputs programmed with LDRx = 11 (LEDOUT register).
(6)
PCA9632
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 27 July 2011
? NXP B.V. 2011. All rights reserved.
13 of 39
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PCA9633BS,118 IC LED DRIVER RGBA 16-HVQFN
PCA9634D,118 IC LED DRIVER RGBA 20-SOIC
PCA9635PW/S911,118 IC LED DRIVER RGBA 28-TSSOP
PCA9685PW,118 IC LED DRIVER RGBA 28-TSSOP
PCA9922PW,118 IC LED DRIVER LINEAR 16-TSSOP
PCA9955TW,118 IC LED DRVR CONST CURR
PCF85102C-2P/03,11 IC EEPROM 2KBIT 100KHZ 8DIP
PCF85103C-2T/00,11 IC EEPROM 2KBIT 100KHZ 8SOIC
相关代理商/技术参数
PCA9632DP2118 制造商:NXP Semiconductors 功能描述:IC LED DRVR TSSOP
PCA9632DP2-T 功能描述:LED照明驱动器 4-BIT FM+I2C-BUS LOW POWER LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9632TK,118 功能描述:LED照明驱动器 4-BIT FM+I2C-BUS RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9632TK2,118 功能描述:LED照明驱动器 4-BIT FM+I2C-BUS RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9632TK2-T 功能描述:LED照明驱动器 4-BIT FM+I2C-BUS LOW POWER LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9632TK-T 功能描述:LED照明驱动器 4-BIT FM+I2C-BUS LOW POWER LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633BS,118 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9633BS-T 功能描述:LED照明驱动器 4BIT I2C FM+ TP LED CON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N